Boat Turning Locks and Flush Lift Rings: Choosing Access Hardware

Quick Answer

Decide the job before the part. If a hatch, locker or console has to stay shut until someone with a key opens it, you need a turning lock: a rotary latch that turns to close rather than pressing a catch, with the pages describing a ninety-degree closing action. If the panel only has to be pulled up, you need a flush lift ring, which sits flat in the panel and rises into a handle. Key or no key is the second decision. Then order by model code, because neither column set on the site carries a legend.

Job Turning lock Flush lift ring What the panel must provide
Panel that has to stay shut to anyone without a key Keyed turning lock, e.g. ALS6250A, two keys supplied Not the job A hole through the panel and a frame edge for the tongue
Locker or console that only has to be held closed Non-keyed stainless or nylon-body turning lock Works if the lid is light and sits down on its own A catch surface behind the panel
Deck plate, seat locker or lazarette lid opened by hand Turning lock as a catch, plus a separate pull Flush lift ring, e.g. ALS7658A A recess for the ring and clearance under the panel
Same panel, two jobs Keyed turning lock at the leading edge Flush lift ring at the trailing edge Two cutouts, both taken from a drawing
Wet cockpit locker The page that describes itself as waterproof Stainless ring with a drain path A drain and a seal you control

Real-World Explanation

A turning lock is a latch you turn rather than press. The product pages describe it as a lockable quarter-turn lock with a ninety-degree closing action, and the key can be removed in both the open and the closed position. That is why the part turns up on lockers, console doors and hatch lids with a frame edge for the tongue to catch on, and why body height matters as much as face diameter — the tongue has to reach the frame, and the body has to clear whatever sits behind the panel.

A flush lift ring is the opposite kind of part. It sits down inside the panel, roughly level with the surface, and lifts into a handle when you hook a finger under it. Owners fit them where a raised handle would catch a foot or a sheet: deck plates, seat lockers, lazarette lids, hatch boards. The range includes a square flush lift ring for hatches and lockers listed as ALS7658A at A 76 / B 58 mm, the round ALS0505A at D 50 mm, the recessed ALS6244B at A 62 / B 44 mm, and ALS6555B at A 65 / B 55 mm beside ALS6656B at A 66 / B 56 mm in one table.

A ring gives you nothing to lock and a lock gives you nothing to pull, which is why the two end up on one panel. On a hatch board or cockpit locker lid the lock sits at the edge nearest the frame, so the tongue has something to bite on, and the ring sits at the opposite edge where your hand arrives. Two cutouts, both measured off the same panel. The turning lock and flush lift ring range lets you pick both in one finish.

The most common mistake in this category is reading “Size: 62 mm” as the cutout. It is not a cutout number; it is the first column of the specification table. The pages use two column systems without explaining either: D1, D2, H1, H2 for some turning locks, A, B, C, D for others, A and B for the flush rings. Nothing on the site states what those letters measure; the only sentence that comes close is a short description line reading “Size: 62MM.” on one turning lock page. One line, one page, no legend.

The D-series pages show how little the first number tells you. ALS6250A reads D1 62 / D2 50.5 / H1 11.5 / H2 37.4 mm on the 316 mirror-polished turning lock page; ALS6250D reads D1 62 / D2 51 / H1 10.7 / H2 70 mm on its own keyed version page. Same D1, different everything else. The A-series behaves the same way: ALS6482A at A 64 / B 82 / C 15 mm, ALS8067A at A 80 / B 67.5 / C 110 mm, and the T-handle pair on the 316 boat turning lock page at A 60 / B 100 / C 52 / D 120 mm for ALS6010A against A 86 / B 100 / C 76 / D 148 mm for ALS6010B.

Two pages drop the letters for a labelled block. The heavy turning lock page gives Surface Diameter 65, Inner Diameter 51, Overall Height 80 and Overall Width 63 mm, and describes the part as waterproof — that page’s description, not a published rating. The oval keyed body gives Surface Length 107, Surface Width 83, Overall Height 151 and Overall Width 94 mm. Those labels read as themselves. D2 50.5 does not become a hole size.

Practical Insights from Marine Hardware Supply

1. Three pages cannot be used as a size source

The model code ALS6252B appears on two pages with two different height values, swapped between them. ALS6250B and ALS6251A carry four identical numbers in an order that runs opposite to the baseline page beside them. And one page is a clone — its slug begins with copy-, its content duplicates another product — so it is a duplicate record, not a specification. A drawing pack built from any of them will disagree with itself.

2. Spelling on the flush ring pages is unreliable

Of the five flush lift ring pages in this range, four spell “Lift” as “Llift” in the product name, including the URL. Search finds them and the parts are real, so do not copy that spelling onto an order sheet or a label. Write square flush lift ring with the model code beside it.

3. Packaging is described in a news post, not on the product pages

The turning lock news post states that a turning lock ships as the lock body, a back plate and fasteners. Treat that as a statement from that article, not a specification read off a product page, because the product pages publish no packing list. If the back plate or the screws decide whether your install happens on Saturday, ask before ordering.

Buying Checklist

Decide the job first. Ask what the panel does when closed. If it has to resist anyone without a key, that is a turning lock. If it only has to be lifted by hand, a flush lift ring is the flatter answer and leaves nothing to catch a foot.

Decide on the key second. The range runs from keyed bodies such as ALS6250A, which ships with two keys, through non-keyed stainless versions, to a nylon family offered with and without a keyed cylinder. A keyed hatch latch decides who gets access, so choose deliberately.

Check the panel material and thickness. The catalogue publishes no door thickness, panel thickness or body depth behind the face, so that comes from a drawing. On a cored composite lid, body depth decides whether the part sits down at all.

Check the cutout and the counterbore. Because the letters are undefined, the cutout has to be confirmed from a dimensional drawing before anyone drills. Read the published numbers as face and body dimensions only, and do not convert D2, B or C into a hole size. A ring recess sized from the face dimension alone will not let the ring finish flush.

Plan the seal and the drain. Neither the locks nor the rings publish a gasket specification. On a wet deck the seal is your detail: bedding compound under the flange, a drain path away from the cutout, a recess that does not hold water against the core.

Match the material to the exposure. The 316 bodies are described as precision cast and mirror polished, which suits salt and visible panels. The nylon family — nylon body with stainless and zinc alloy parts — suits lockers where a black finish and a lower-cost body make sense. The nylon pages publish no dimensions, so those come from a drawing too. Order the ring in the same finish family so the lock and the pull match on one lid.

Confirm packing and spare keys. Ask what is in the box: body, back plate, fasteners, keys, and how many keys. On a charter boat or a dealer handover the spare key count is part of the specification, so get the packing list written onto the quotation.

Decision Guide

Choose a keyed turning lock if

The locker holds tools, electronics or anything a guest should not open. ALS6250A with its two supplied keys and ALS6250D are the two D1 62 mm bodies to compare, and the differences sit in the other three columns.

Choose a non-keyed turning lock if

The panel is an access lid that only has to stay shut underway and anyone aboard may open it. The same rotary action without a cylinder keeps the install simple, and a nylon body covers the locker where black reads better.

Choose the waterproof version if

The locker is wet by design — a cockpit sole locker, an anchor well, a deck plate that takes spray. The heavy version is the one page here that describes itself as waterproof, at Surface Diameter 65 mm and Overall Height 80 mm. Confirm the seal detail on the drawing.

Choose a nylon body if

You want a low-profile black locker latch with stainless and zinc alloy internals, with or without a keyed cylinder. It suits interior lockers and tender seats, and the drawing request is mandatory because no dimensions are published.

Choose a flush lift ring if

The panel only has to be pulled, or a lock already sits at the other edge. ALS7658A at A 76 / B 58 mm and ALS6244B at A 62 / B 44 mm are the larger and smaller square bodies, ALS0505A is listed at D 50 mm, and ALS6555B / ALS6656B are two close sizes in one square family.

Buy by model code, not by description. Any number used for a cutout comes from a drawing, and the letter columns are labels without a legend — a way to tell two models apart, not a measuring instruction.

Need Help Choosing or Sourcing?

Send the panel, the opening you already have and the model code you are weighing up, and we will return the drawing that shows the cutout, the body depth and the ring recess. Where standard bodies do not suit your lid, the same tooling covers custom sizes, alternate finishes and private-label packing through OEM and ODM work, with samples before a production run.

Refitting one locker or stocking a dealer shelf, tell us what the panel has to do and we will quote model, keys and packing list together.


Post time: Nov-16-2026